防靜電措施可能也是大多數人想問的問題，尤其是在安裝電纜橋架的過程中，往往會出現一些小問題。如何采取措施避免工作的順利完成？今天濟南電纜橋架廠家就來教教大家。

Anti static measures may also be the question most people want to ask, especially in the process of installing cable tray, some small problems often occur. How to take measures to avoid the smooth completion of the work? Today, Jinan cable bridge manufacturer will teach you.

1.預處理

1. Pretreatment

意圖:去除工件表面的油污、灰塵、鐵銹，在工件表面形成一層耐腐蝕的“磷化層”，可以增加噴涂層的附著力。

Intention: remove the oil stain, dust and rust on the surface of the workpiece, and form a corrosion resistant "phosphating layer" on the surface of the workpiece, which can increase the adhesion of the spraying layer.

主要工藝流程:脫脂、除銹、磷化、鈍化。經過前處理后，工件表面無油、無銹、無灰塵，在原有銀白色光澤的表面上形成均勻粗糙的灰色磷化膜，可防銹，增加噴涂層的附著力。

Main process flow: degreasing, rust removal, phosphating and passivation. After pretreatment, the workpiece surface is free of oil, rust and dust. A uniform and rough gray phosphating film is formed on the original silver white shiny surface, which can prevent rust and increase the adhesion of the spraying layer.

2.靜電噴涂

2. Electrostatic spraying

意圖:將粉末涂料均勻噴涂在工件表面，尤其是電纜橋架(包括單純發生靜電屏蔽的位置)，大概使用高性能靜電噴塑機完成噴涂。

Intention: Spray the powder coating evenly on the surface of the workpiece, especially on the cable tray (including the position where electrostatic shielding occurs only), and probably use a high-performance electrostatic spraying machine to complete the spraying.

工藝:應用靜電吸附原理，在工件表面均勻噴涂一層粉末涂料；落下的粉末由回收系統回收，過篩后可重復使用。

Process: Apply electrostatic adsorption principle to evenly spray a layer of powder coating on the surface of the workpiece; The fallen powder is recovered by the recovery system and can be reused after sieving.

3.高溫固化

3. High temperature curing

目的:將電纜橋架表面的粉末涂料加熱到規定的溫度并保溫相應的時間，使其熔化、流平、固化，進而得到工件所需的表面。

Purpose: Heat the powder coating on the surface of the cable tray to the specified temperature and keep it warm for a corresponding time, so that it can be melted, leveled and solidified, and then obtain the required surface of the workpiece.

工藝:將噴涂后的工件推入固化爐，加熱預定溫度(一般為185度)，保溫相應時間(15分鐘)；開爐，取出，冷卻，即得產品。

Process: push the sprayed workpiece into the curing furnace, heat the predetermined temperature (generally 185 ℃), and keep the temperature for a corresponding time (15 minutes); Open the furnace, take it out and cool it to get the product.

提示:加熱及控制系統(包括電加熱、燃油、燃氣、燃煤等多種加熱方式)+保溫箱=固化爐。

Prompt: heating and control system (including electric heating, fuel oil, gas, coal and other heating methods)+incubator=curing furnace.

4.裝飾和處理

4. Decoration and treatment

目的:使靜電噴涂后的工件達到特殊的外觀。

Purpose: To make the workpiece after electrostatic spraying reach a special appearance.

有關電纜橋架的防靜電處理措施相關內容就講解到這里了，您對此有什么不了解的地方就來我們網站http://www.yeeones.com咨詢吧！

That's all for the anti-static treatment of cable tray. If you don't know anything about it, please come to our website http://www.yeeones.com Consult!