電纜橋架的托臂支架和護罩是用來做什么的呢？下面由山東電纜橋架小編為您做一下說明。

What are the bracket and shield of cable tray used for? The following is a brief description of Shandong cable tray.

電纜橋架的托臂支架是支撐電纜橋架和電纜的主要部件，它由立柱、立柱底座、托臂等組成。我廠生產的托臂支架是根據日本、德國的同類產品設計而成；

The bracket of the cable tray is the main part supporting the cable tray and cable, which is composed of column, column base, bracket, etc. The arm bracket produced by our factory is designed according to similar products in Japan and Germany;

它具有結構簡單、重量輕、成本低、強度大、造型美等優點，可滿足不同環境條件（工藝管道架上、樓板下、墻壁上、電纜溝內）安裝成不同形式(懸吊式、直立式、側壁式、單邊、多邊和多層）等的需要。

It has the advantages of simple structure, light weight, low cost, large strength, beautiful shape, etc., and can meet the needs of different environmental conditions (above the process pipe rack, under the floor, on the wall, in the cable trench) to install in different forms (suspended, vertical, side wall, unilateral, multilateral and multi-layer).

電纜橋架如需多層重載荷吊裝時，要盡量采取雙邊敷設、避免偏載過大。托臂支架部分其表面處理有電鍍鋅、熱度鋅、噴漆、噴塑四種。

If multi-layer heavy load hoisting is required for cable bridge, double side laying shall be adopted as far as possible to avoid excessive eccentric load. The surface treatment of the bracket part of the corbel can be divided into four types: galvanization, hot galvanizing, painting and plastic spraying.

電纜橋架護罩是一種用于電力或通訊電纜走線工程的電纜橋架上的護罩，由鋼板壓制而成，該電纜橋架護罩的頂面和頂面兩邊的折邊都為凹凸面形狀，頂面上的凸面和凹面相間連續設置。

The cable tray cover is a cover on the cable tray used for power or communication cable routing engineering, which is pressed by steel plates. The top surface and the folding edges on both sides of the top surface of the cable tray cover are concave and convex, and the convex and concave surfaces on the top surface are set continuously.

每一個凸面和凹面單元的兩頭向同一方向彎曲成折邊，凸面與凹面之間的高差小于8毫米，新型的高強度結構電纜橋架護罩，由于整個蓋平面采用的凹凸狀的結構造型，因此增加了該護罩的鋼性鋼度。

The two ends of each convex and concave unit are bent in the same direction to form a folded edge, and the height difference between the convex and concave is less than 8 mm. The new high-strength structure cable bridge shield has increased the rigidity of the shield due to the concave and convex structural modeling used in the entire cover plane.

由于鋼性強度的提高，可以采用較薄的材料制造，如采用同樣的板厚其強度超過原來的兩倍以上，其優點主要是降低成本、產品不易變形。

Due to the improvement of steel strength, thinner materials can be used for manufacturing. If the same plate thickness is used, its strength is more than twice of the original strength. Its advantages are mainly to reduce costs and prevent products from deformation.

電纜橋架托臂支架和護罩的作用就講解到這里了，您對此有什么想咨詢的問題可以隨時來我們網站http://www.yeeones.com了解！

This is the end of the function of the cable bridge bracket and shield. If you have any questions about this, you can come to our website at any time http://www.yeeones.com Understand!